8-6” ASIC Crypto Mining Silencer / Cooling Kit (L7, D7, S19pro, S19, KD5, LT5)

Description

NEW 8" ASIC Miner Silencing Kit with a
6" Outlet
.
Note:
This is a complete kit.... Everything you will need
BUT
the Blower/Fan.
Why don't you sell the complete kit with the fan?
Honestly, It doesn't make since for me to buy the blower on Amazon, ship it to my office, add it to your kit, pay for the extra shipping back to you, pay eBay 12% in fees, buy a bigger box, etc.... all I was doing was charging you more for all of these fees....when you can have it dropped shipped directly to you.  The fan is obtainable by searching Amazon for “AC Infinity S8”.
https://www.amazon.com/dp/B07J9PTYRN/ref=cm_sw_r_cp_api_glt_i_AVZ7TNV9XCB0JW362KK7?_encoding=UTF8&psc=1
What miners do they work with?
They will work the following Bitmain Miners: D7, L7, S19j Pro, S19 Pro, S19, KD5, LT5 & the new S19 XP. They will also work with most Dual Fan ASIC's (You may just need to purchase special Fan Emulators... Included are inline 4 pin emulators).  If you are mounting them on a ASIC that might have a PSU or controller hanging off one end (like some of the s19j Pro's have), blocking the inlet adaptor from bolting up, just reverse it... blow in from the unblocked side.... It really doesn't matter.
Is it easy to install?
All you do is remove the existing fans, and plug in the four 4 Pin Fan Spoofers (Included!) on the AISC's control board where the original fans would normally plug in.  You mount the adaptors to the existing fan locations where the fan's would normally mount with the screws we provide (Not the ones that mount the old fans!) and clamp the 800 CFM blower (Provided by you!) to the bottom flange (as shown in the photos).
Can they be mounted Vertically to the wall?
Yes, they can also be mounted vertically on a sheet of plywood (This is the way I use them).  Mounting them vertically on the wall takes up less space, you don't need a shelving rack, and it's easy to add a 6" standard dryer hose to a vent outside for the exhaust.  I promise if you add these to your garage wall, your wife will let you buy more!  I do recommend a screen or a filter if there is a lot of dirt or kids fingers......
Are they Quiet?
These blowers are very quiet.. especially if you reduce the speed to 3/4 of maximum speed, which is all you need...  Just watch your temps......and understand,that YOU have to control the blower speed... not the ASIC.   The safest thing to do is just run them full speed.  The good news, is the sound is quite pleasing.... a soft hum vs an annoying screaming sound the original fans make!  But on this side note.... remember, we are doing nothing to quiet the PSU's and in many cases, they are also louder than this blower......but the whole thing will be MUCH quieter than the original fans!!!
What are the Adaptors made of?
The adaptors are printed out of ABS Plastic using 6 industrial printers modified for printing temperature of up to 650° F.
A little information about 3D printing plastics…
All 3D printing material (PLA, ABS, Nylon, TPU, etc...) have what the industry calls a “
Glass Transition Temperature
”. This is the temperature in which the plastic starts to get “soft or pliable”. PLA Plastic (The most common type of 3D printer material) has a Glass Transition Temperature between 50° and 80° Celsius. If you think about this for a minute….The chip temperature in your ASIC get to these numbers!  This is why we only use ABS Plastic which has a Glass Transition Temp of 110° Celsius.
I am running Industrial 6 printers constantly on this project. This is why I don’t list too many at a time….I don’t want to get too far behind. But please understand I will get them out to you as soon as I can, and I ship the first ones purchased first (first in first out).
What is included in the kit?
One - ABS S-8 Inlet adaptor (Connects directly to the S8 Blower and your ASIC)
One - ABS 6" Outlet adaptor (Connects to the Discharge Side of your ASIC and Discharges the hot air to a 6" dryer hose)
One - Stainless Steel 8" Clamp (To attach the S8 Adaptor to the AC Infinity Blower)
Sixteen - M8 x 12mm Screws (To mount both adaptors where the original fans mounted)
Four - 4 Pin (Inline) Fan Emulators (Plugs in where the original fans did)
Installation Instructions
Free Shipping!!!!!
What is
NOT
included?
The Blower / Fan (It is easily obtainable on Amazon..Just search for AC Infinity S8)
The 6" Discharge hose, clamps, vents, etc... (These are all items that you can obtain from Home Depot or Amazon)
The #8 screws used to mount to the wall / plywood.... (The recommended size is #8 countersink wood screws... 3/4" long)
Is this better than Immersion Mining Tanks?
So, I actually have an Immersions system with 10 ASIC's running in BitCool Engineered Fluid.  It works well, and you do get amazing results.... But, you are taking the heat from the ASIC, transferring it to the oil, then taking the oil and transferring the heat (via the cooler) to Air.  It is VERY expensive to obtain, you have to buy the tank, the pump, the oil, the cooler, electricity, etc...  This option takes the heat directly to air..... one step removed.
If you have any additional questions, please don't hesitate to ask... we also have several other models available (M31S, Z15's, L3's, S9's, etc...)
Enjoy,
John.
P.S.:  If you have any doubts.... please take the time to look at the reviews..... I could post them here, but there are so many.....